- Hot search:
DIN 65434:2020 pdf free download
DIN 65434:2020 pdf free download.Luft- und Raumfahrt -Hülsen -Wanddicke 0,5 mm für Verbindungselemente mit reduziertem Senkkopf; Text Deutsch und Englisch.
1 Scope
This DIN 65434 specifies the characteristics of sleeves, wall thickness 0,5 mm, for fasteners with reduced countersunk head used together with screws and bolts to replace oversize shank fasteners for aerospace applications.
Sleeves to this document may be used to reduce bearing and contact pressure on composite materials.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
DIN 65435, Aerospace — Sleeves for fasteners — Technical specification
DIN EN 2424, Aerospace series — Marking of aerospace products
DIN EN 2437, Aerospace series — Chromate conversion coatings (yellow) for aluminium and aluminium alloys DIN EN 2516, Aerospace series — Passivation of corrosion resisting steels and decontamination of nickel base alloys
DIN EN 4473, Aerospace series — Aluminium pigmented coatings for fasteners — Technical specification
DIN ISO 2768-1, General tolerances — Tolerances for linear and angular dimensions without individual tolerance indications
LN 9 368-1, Aerospace — Designation of surface treatments —Composition of code numbers, indications in
design documents, survey
LN 9368-3 Aerospace — Designation of surface treatments — Part 3: Code numbers for methods of chemical treatments
LN 9368-5, Aerospace — Designation of surface treatments — Part 5: Code numbers for methods of cathodic treatments
German Aviation Materials Manual, Part I:
WL 1.4943 -1, Aerospace — Heat-resisting precipitation-hardening nickel-chromium-titanium steel with approx. 0,03 C, 25 Ni, 15 Cr, 1,8 Ti, consumable electrode remelted — Sheet, plate and strip
WL 1.4944-2, High temperature precipitation-hardening nickel-chromium-titanium steel with about 0.06C- 25Ni-l5Cr-2.1 Ti-i .2Mo — Rods and forgings
WL 3.3214-1,Aerospace — Wrought aluminium alloy with approx. 1,0Mg — 0,6 Si — 0,3 Cu — 0,20 Cr — Sheet and plate
3 Terms and definitions
No terms and definitions are listed in this document.
DIN and DKE maintain terminological databases for use in standardization at the following addresses:
— DIN-TERMinologieportal: available at https://www.din.de/go/din-term
— DKE-IEV: available at http://www.dke.de/DKE-IEV.DIN 65434:2020 pdf free download.
All resources on this website are from the Internet. It is only for personal study and research. No one is allowed to use it for any commercial purpose. If you need, please buy the genuine standard. If there is any infringement of your copyright, please contact the webmaster in time, and I will correct it immediately.
- Maybe you like
- More
- Latest Updates
- ISO 287-2009 pdf free download
- ISO 527-5-2009 pdf free download
- ISO 659-2009 pdf free download
- ISO 660-2009 pdf free download
- ISO 712-2009 pdf free download
- ISO 725-2009 pdf free download
- ISO 730-2009 pdf free download
- ISO 927-2009 pdf free download
- ISO 2041-2009 pdf free download
- ISO 3040-2009 pdf free download
- ISO 3506-2-2009 pdf free download
- ISO 3506-3-2009 pdf free download