- Hot search：
UL 62841-2-9-2017 pdf free download
UL 62841-2-9-2017 pdf free download.Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery — Safety — Part 2-9: Particular Requirements For Hand-Held Tappers And Threaders.
This clause of Part 1 is applicable.
8 MarkIng and Instructions
This clause of Part 1 is applicable, except as follows:
In addition the tool shall have the following marking:
— maximum diameter, in millimetres (for tappers) or in inches (for threaders), of the thread
which can be cut.
NOTE According to the International System of Units, only SI units should be used. Nevertheless, some pipe diameters and threads are still specified In inches internationally.
For tappers, the diameter shall refer to a unified ISO thread to be cut into steel having a tensile strength of 390 N/mm2 and a thickness of twice the thread diameter, unless otherwise indicated on the tool.
For threaders, the diameter shall refer to a taper style thread in accordance with ISO 7-1 to be cut on steel tubes in accordance with ISO 65, unless otherwise indicated on the tool.
For threaders. the additional safety instructions as specified in 184.108.40.206 shall be given. This part may be printed separately from the ‘GeneraI Power Tool Safety Wamings’.
8.14,1,101 Threader safety warnings
a) Always use the support device provided with the tool. Loss of control during operation can result in personal injury.
b) Keep sleeves and jackets buttoned while operating the tool. Do not reach across the tool or pipe. Clothing can be caught by the pipe or the tool resulting in entanglement.
C) Only one person must control the work process and tool operation. Additional people involved in the process may result in unintended operation and personal injury.
d) Keep floors dry and free of slippery materials such as oil. Slippery floors invite accidents.
8.14.2 a) Addition:
101) for threaders: instructions for mounting and use of the support device.
8.14.2 b) Addition:
101) for threaders: instructions to always use the support device supplied with the tool;
102) for threaders with multiple gear box settings: information about which gear box setting is to be used for each pipe diameter.
9 ProtectIon against access to Uve parts
This clause of Part 1 Is applicable.
This clause of Part 1 is applicable.
11 Input and current
This clause of Part i is applicable, except as follows:
For threaders, the requirements of this clause are replaced by the following:
The rated input or rated current shall be at least 100 % of the measured input or current applying the torque in Table 101,
Compliance is checked by measuring the power input or current of the tool when stabilized while all circuits which can operate simultaneously are in operation.
For tools marked with one or more rated voltages, the test is made at each of the rated voltages. For tools marked with one or more rated voltage ranges. the test is made at both the upper and lower limits of the ranges. For tools with multiple gear box settings, the test is made at each specified gear box setting in accordance with 8.14.2 b). The highest value of input or current is applicable.UL 62841-2-9-2017 pdf free download.
All resources on this website are from the Internet. It is only for personal study and research. No one is allowed to use it for any commercial purpose. If you need, please buy the genuine standard. If there is any infringement of your copyright, please contact the webmaster in time, and I will correct it immediately.
- Maybe you like
- Latest Updates
- ISO 287-2009 pdf free download
- ISO 527-5-2009 pdf free download
- ISO 659-2009 pdf free download
- ISO 660-2009 pdf free download
- ISO 712-2009 pdf free download
- ISO 725-2009 pdf free download
- ISO 730-2009 pdf free download
- ISO 927-2009 pdf free download
- ISO 2041-2009 pdf free download
- ISO 3040-2009 pdf free download
- ISO 3506-2-2009 pdf free download
- ISO 3506-3-2009 pdf free download